home *** CD-ROM | disk | FTP | other *** search
/ Aminet 40 / Aminet 40 (2000)(Schatztruhe)[!][Dec 2000].iso / Aminet / hard / hack / TestGear2.lha / TestGear2 / ReadMe < prev    next >
Encoding:
Text File  |  2000-09-24  |  4.3 KB  |  105 lines

  1.  
  2.                Well done you have now reached TestGear Disk 2.
  3.                -----------------------------------------------
  4.  
  5.   I have assumed (one must NEVER make assumptions) that you have progressed
  6.   through TestGear Disk 1 (TestGear1.lha and TestGear1.readme) and made the
  7.   simple test leads for the first four projects. The projects on this disk
  8.   are more sophisticated. Some will be connected to the parallel port.
  9.   Take great care when connecting to, and disconnecting from this port.
  10.   There will be NO more references to switching OFF the AMIGA before
  11.   connecting hardware after this text. Also there will be NO more references
  12.   about the use of solvents, glues, dangerous tools and any high electrical
  13.   voltage hazards after this text. By now you should be well aware of any
  14.   problems and dangers that exist with electronic equipment. So here are the
  15.   final warning notes to remind you.
  16.  
  17.                                  WARNING.
  18.                                  --------
  19.  
  20.   1) DISCONNECT any faulty equipment under test from the MAINS supply.
  21.   2) If a DC supply is used do NOT reverse polarity the connections.
  22.   3) Do NOT power up any electronic item until it is safe to do so.
  23.   4) CHECK and RECHECK all of your construction and repair work thoroughly.
  24.   5) Handle ALL tools used with care.
  25.   6) Beware of ALL types of solvents, glues and etching fluids.
  26.   7) NEVER leave a soldering iron switched on unattended.
  27.   8) KEEP everything OUT of the reach of small children.
  28.   9) Switch OFF the AMIGA before connecting any hardware.
  29.  10) And finally read 1) to 9) again.
  30.  
  31. ----------------------------------------------------------------------------
  32.  
  33.   Important:-
  34.   -----------
  35.  
  36.   If you try any of the software that requires the Analogue to Digital
  37.   Converter without the Analogue to Digital Converter connected the system
  38.   should NOT crash, however the display will always read a maximum value
  39.   for that particular piece of software giving you an idea of the
  40.   capabilities of that software. Enjoy constructing your projects.
  41.  
  42.   Because of the way the AMIGA is made you MUST fit a blank RCA/PHONO plug
  43.   into any UNUSED Audio Output Socket to obtain the calibrated results of
  44.   the software in use.
  45.  
  46. ----------------------------------------------------------------------------  
  47.  
  48.   There will no longer be a ~Tools Required~ list in each project's ~Info~
  49.   file. You should now be well aware that you require a standard set of
  50.   electronic and hobbyist tools to make all the projects. However any
  51.   special tools that may be required will be listed, along with any source
  52.   for that tool.
  53.  
  54. ----------------------------------------------------------------------------
  55.  
  56.   Calibration Equipment:-
  57.   -----------------------
  58.  
  59.   To calibrate most of the projects from now on you WILL require some dry
  60.   cells or batteries. I decided on using the ~EVEREADY~ RED types as these
  61.   are well known in the UK. They were all NEW, as this gives a definitive
  62.   starting point to work from. However any ZINC/CHLORIDE types should be OK.
  63.   Alkaline batteries were NOT used to calibrate any projects.
  64.   
  65.   1) R6..............  1.5 Volt nominal, RED body type, (ULTRA PLUS).
  66.   2) 6F22............  9 Volts nominal, RED body type, (ULTRA PLUS).
  67.  
  68.   These are available from most retail outlets.
  69.  
  70. ----------------------------------------------------------------------------
  71.  
  72.   Acknowledgements:-
  73.   ------------------
  74.  
  75. First of all many thanks to my wife Tricia who allows me to spend many hours
  76. on my computers.
  77.  
  78. Also to David Benn and Herbert Breuer for the ACE/AIDE combination supplied
  79. on an AMIGA FORMAT floppy disk which made it easy to compile this program.
  80.  
  81. Also to Laurence J Greatorex for giving these a shakedown on his A1200 with
  82. a Turbo LC '030 accelerator board and 32MB of fast ram, also to Bob Eva for
  83. testing on his A1200, with a total of 10MB of ram, and also to all the
  84. other people that have given any of these projects a rigorous testing.
  85. And finally to anyone else who I may have neglected or forgotten.
  86.  
  87. ----------------------------------------------------------------------------
  88.  
  89.     Mr Barry Walker,
  90.     70 King George Road,
  91.     Loughborough,
  92.     Leicestershire,
  93.     LE11 2PA,
  94.     England.
  95.  
  96.     Email to:-
  97.  
  98.     106161.3245@compuserve.com
  99.     or
  100.     wisecracker@tesco.net
  101.  
  102.     BYE.....
  103.  
  104. ----------------------------------------------------------------------------
  105.